Yesterday I noticed it didn't work on 1, 2, or 3 only on Max. Today even on max it doesn't work but it makes the battery gauge dip way down, from 13.8 to about 7. As soon as I turn the switch back to 3 the gauge jumps momentarily to around 17 and then back to 13.8. I'm not sure if its just...
...fit my truck? I have a 1997 Mazda b4000, im not sure if it will fit or if its compatible..... anything that fits on the ford ranger will fit my truck also because its the exact same engine... but im still unsure.. thanks
My 2001 Ford Focus started squealing when the blower was on, whether it was a/c or heat and then a couple of days ago the blowing just stopped. I've had to replace the blower motor resistor switch twice over the past year or two. I read that if the blower motor resistor switch was going out that...
i was wondering if someone could tell me where the heater blower motor is, and what exactly it looks like on a 1993 gmc jimmy. It needs to be replaced but i cant find it. if you have a link that shows a picture of it already on the vehicle that would be nice thanks
from few days my laptop is getting overheated, and it easily gets to 75 C. I don't want to take a risk to open laptop by myself and clean the heat sink. What I want to ask is that can I use blower or hair dyer instead of compressed air can. Will blowing the air through the air vent will work ?
...still be caused by the resistor? After removing and replacing the battery the heater fan stopped working. I know if you have just high speed it's the resistor. But it don't work at any speed. Checked the fuse and relay in the fuse box under the hood and they are ok.
Is there any additives that are good for the engine that reduce smoke or certain oils that are better than others to reduce smoke output for my Ariens snow blower?
THANKS!
i have a 1998 silverado 1500 turbo diesel, when i start the truck the blower motor blows on full blast no matter what the setting is, anyone no whats wrong???
I have a 1991 Mazda mx6 and the ac blower motor only functions on 1 and 2 speeds not high 3 and 4 already replaced resistor and still the same what's the problem please help
I have a 1991 Mazda mx6 and the ac blower motor only functions on 1 and 2 speeds not high 3 and 4 already replaced resistor and still the same what's the problem please help
I have a 1991 Mazda mx6 and the ac blower motor only functions on 1 and 2 speeds not high 3 and 4 already replaced resistor and still the same what's the problem please help
I have a 454 in a boat that supports a cast rotating assembly 8.3 to 1 compression, comp cams xtreme energy cam 278H with a non-striped 6-71 blower. I am running 1/2 pitch pulleys, top is 40 teeth, bottom is 37 teeth, being underdrive. Can I safely run a 39, 38 or 37 on the top??? Or is that too...
holding the acelerator most of the time? its been out in every weather condition lol! but my question is why doesnt it run for long inless im pressing up and down on the accelerator! its got gas and oil any other ideas?
It happened around noon today and then it stopped after I shut my car off for about 20 minutes. I haven't turned it back on in fear that something is wrong. It looks just like steam (white smoke) and when I put my hand in front of it, my hand becomes wet. We just recently installed a new A/C...
ok 1st off i had to bypass the blower motor because the switch works but does not turn on the blower motor... 2nd the blower motor does not blow very hard its a very lite breeze anybody got any answer i would love to know what the problems is......btw i have spent $450 on the a/c to charge it...
the a/c or "vent" on my vehicle will only work part times. I think its the blower motor?? in my previous vehicle I was experiencing same problem.
the air blowing from my vents will work sometimes. like it cuts in and out sometimes... but when it does cut out, if I smack my dashboard, right...
I checked the fuses and relays, they appear fine. I'm not sure if it's fan switch or the fan motor but I need advice on how to access the switch and the front fan motor.